Survivalist Blog

Survival Forums, News, Political Opinion and Discussions.

Building A Chicken Yard Part 1

For those of you who are planning on raising chickens after SHTF / TEOTWAWKI, have you put any thought into building the chicken yard? People who have lived in a rural area may have been exposed to the hard work of building a chicken yard. But people who live in the city or urban areas, the vast majority have no idea how much hard work building a chicken yard takes.

As some of yall may know my wife and I are planning on moving to a rural area of southeast Texas. We have moved past the planning phase are are moving to the implementation phase.Barred Rock chicken

When my wife make the move to the homestead, the chicken coop will be loaded on a trailer, taken to the farm, unloaded and bumped up to the new chicken yard. Before all of that can happen the new chicken yard has to be built.

After spending a lot of time on the dimensions, how many square feet each chicken needs, how many chickens I wanted, and room for growth,,, I came up with a chicken yard that is 75 feet long and 30 feet wide.

Dimensions

The chicken yard is sitting between a driveway going to a garden area, an oak tree I do not want to cut down and  a creek.  The width of the chicken yard could be no wider than around 30, or maybe 35 feet at the widest.

On the length the chicken yard could have been up to 100 feet long.  But at 100 feet the yard would have been getting close to the garden area.

In the end, I decided to go with a 75 foot long chicken that is 30 feet wide, which provides 2,250 square feet.

Square feet per chicken

If chickens do not have enough room they start pecking at each other.  The pecking promotes aggression, injuries, infection and in some cases the infections lead to death.

Once a chicken develops an injury that bleeds, other chickens will peck at the wound.  The wound is unable to heal, it gets infected and the chicken dies from infection.

A general rule of thumb is each chicken needs at least 10 square feet in the yard.

My personal goal is to be able to raise at least 100 chickens comfortably.

2,250 square feet will provide 100 chickens with 22.5 square feet for each chicken.

Room for growth

My goal is to have on average around 50 – 75 chickens.  But with 100 chickens having 22.5 square feet each, this leaves a lot of room for growth.

Something I thought about doing is having enough room to raise 30 – 50 meat chickens in the spring, then butcher them before the heat of the summer sets in.  If my wife and I can put at least 30 – 40 chickens in the freezer we that would supply us with enough chicken meat for a year.

Another thought is rather than raising meat chickens, raise heritage chicken breeds then butcher them as they are needed.

Construction

The chicken yard was started by using 3 foot sections of 3/4 inch round bar to stake out the corners.

Measure the length, width and diagonally to make sure the dimensions were correct.

For corner post I decided to use crossties.  A local hardware store just happens to sale used crossties for $10 each.

A shovel was used to break the ground, machete and chainsaw used to cut the tree roots, and post hole digger to dig a hole about 3 feet deep.

A few rocks about 1/2 the size of a fist were dropped into the bottom of the hole.

Crosstie was placed in the hole.

Rocks were poured around the base of the crosstie.

2 bags of quickcrete were poured into the hole, a 5 gallon bucket of water was then poured on top of the quickcrete.  The mixture was stirred by round bar and by hand.

Use a 4 foot level to level the corner post.

If needed, drive stakes into the ground, then use a board going between the stake and cross tie to hold the post in place.

Quickcrete was allowed to dry for 2 days before the gate was installed.

The gate nearest the chicken coop is 4 feet wide and has a section of cattle panel tack welded along the tubing of the gate.  If the cattle panel wide does not provide enough protection to keep predators out I will tack weld another section of wire panel to the gate.

2x4s were used as spacers between the bottom of the gate and the ground.

The gate hinges screw into the corner post with something that looks likes a lagbolt.  Before the hinges were installed a 3/8 inch pilot hole was drilled into the crosstie.

A pipe wrench was used to screw the hinges into the crosstie.

Once the gate has been hung on the corner post we are ready to set the opposing post.

Position the gate so that it is aligned with the fence, mark the ground where the other post is going, dig the hole for the other post.

Repeat with the rocks and quickcrete.

Place a level on the gate to make sure it is level.

To hold the second post in place while the quickcrete was drying, I used a couple of 2x4s as spacers between the gate and cross tie and ratchet straps to hold the second post tight against the boards.

From the post that were just set decide which side of the wire you wish to run first.

Go to the other end of the fence and set the other corner post.

After the quickcrete has dried string a few inches above the ground between the two corner post.  The string will act as a guide for setting the fence post.  I used white trotline string between my corner post.  Trotline string is cheap and it is strong.

Have someone hold a tape measure on the corner post, then space the fence post equally along the run.

For my chicken yard I used 6 foot long T-post – 2 feet in the ground and 4 feet above ground.

Use a T-post driver to set the post to the desired depth and/or height.

Now it is just a matter of attaching the wire to the corner post and fence post.  For my chicken yard I used 48 inch tall 2×4 welded wire.

Conclusion

That pretty much sums it up for now.  In the next article we will be talking about setting the other corner post that the gates are not attached to and how to keep predators out of the chicken yard.

[flagallery gid=18 name=Gallery]

 

 

 

Related Post

Share on FacebookShare on Google+Tweet about this on TwitterShare on LinkedInPin on PinterestShare on Tumblr
The following two tabs change content below.
Kevin Felts was born and raised in southeast Texas, graduated from Bridge City high school Bridge City Texas, and attended Lamar College in Port Arthur Texas. Hobbies include fishing, hiking, hunting, blogging, sharing his politically incorrect opinion, video blogging on youtube, survivalism and spending time with his family. In his free time you may find Kevin working around the farm, building something, or tending to the livestock

Latest posts by Kevin Felts (see all)

Kevin Felts © 2017 Frontier Theme